Bluetooth:btintel: Print firmware SHA1 #11

kirankrishnappa-intel · 2023-11-23T14:01:46Z

Intel Read Version event contains a TLV(0x32) having firmware sha1 in operational image.

[ 705.484460] Bluetooth: hci0: Device revision is 0
[ 705.484463] Bluetooth: hci0: Secure boot is enabled
[ 705.484464] Bluetooth: hci0: OTP lock is disabled
[ 705.484465] Bluetooth: hci0: API lock is disabled
[ 705.484466] Bluetooth: hci0: Debug lock is disabled
[ 705.484467] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[ 705.484468] Bluetooth: hci0: Bootloader timestamp 2019.40 buildtype 1 build 38
[ 705.484473] Bluetooth: hci0: No support for _PRR ACPI method
[ 705.484637] Bluetooth: hci0: Found device firmware: intel/ibt-0041-0041.sfi
[ 705.484676] Bluetooth: hci0: Boot Address: 0x100800
[ 705.484677] Bluetooth: hci0: Firmware Version: 151-42.23
[ 706.938396] Bluetooth: hci0: Waiting for firmware download to complete
[ 706.938400] Bluetooth: hci0: Firmware loaded in 1419688 usecs
[ 706.938533] Bluetooth: hci0: Waiting for device to boot
[ 706.963597] Bluetooth: hci0: Malformed MSFT vendor event: 0x02
[ 706.963623] Bluetooth: hci0: Device booted in 24611 usecs
[ 706.965999] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0041-0041.ddc
[ 706.967555] Bluetooth: hci0: Applying Intel DDC parameters completed
[ 706.970572] Bluetooth: hci0: Firmware timestamp 2023.42 buildtype 1 build 73111
[ 706.970581] Bluetooth: hci0: Firmware SHA1: 0x2e575f2a
[ 707.050538] Bluetooth: MGMT ver 1.22

Some layers such as SMP depend on getting notified about encryption changes immediately as they only allow certain PDU to be transmitted over an encrypted link which may cause SMP implementation to reject valid PDUs received thus causing pairing to fail when it shouldn't. Fixes: 7aca0ac ("Bluetooth: Wait for HCI_OP_WRITE_AUTH_PAYLOAD_TO to complete") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This makes it possible to bind a PA sync socket to a number of BISes before issuing the BIG Create Sync command. Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

For ISO Broadcast, all BISes from a BIG have the same lifespan - they cannot be created or terminated independently from each other. This links together all BIS hcons that are part of the same BIG, so all hcons are kept alive as long as the BIG is active. If multiple BIS sockets are opened for a BIG handle, and only part of them are closed at some point, the associated hcons will be marked as open. If new sockets will later be opened for the same BIG, they will be reassociated with the open BIS hcons. All BIS hcons will be cleaned up and the BIG will be terminated when the last BIS socket is closed from userspace. Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

syzbot found a potential circular dependency leading to a deadlock: -> bluez#3 (&hdev->req_lock){+.+.}-{3:3}: __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599 __mutex_lock kernel/locking/mutex.c:732 [inline] mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784 hci_dev_do_close+0x3f/0x9f net/bluetooth/hci_core.c:551 hci_rfkill_set_block+0x130/0x1ac net/bluetooth/hci_core.c:935 rfkill_set_block+0x1e6/0x3b8 net/rfkill/core.c:345 rfkill_fop_write+0x2d8/0x672 net/rfkill/core.c:1274 vfs_write+0x277/0xcf5 fs/read_write.c:594 ksys_write+0x19b/0x2bd fs/read_write.c:650 do_syscall_x64 arch/x86/entry/common.c:55 [inline] do_syscall_64+0x51/0xba arch/x86/entry/common.c:93 entry_SYSCALL_64_after_hwframe+0x61/0xcb -> bluez#2 (rfkill_global_mutex){+.+.}-{3:3}: __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599 __mutex_lock kernel/locking/mutex.c:732 [inline] mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784 rfkill_register+0x30/0x7e3 net/rfkill/core.c:1045 hci_register_dev+0x48f/0x96d net/bluetooth/hci_core.c:2622 __vhci_create_device drivers/bluetooth/hci_vhci.c:341 [inline] vhci_create_device+0x3ad/0x68f drivers/bluetooth/hci_vhci.c:374 vhci_get_user drivers/bluetooth/hci_vhci.c:431 [inline] vhci_write+0x37b/0x429 drivers/bluetooth/hci_vhci.c:511 call_write_iter include/linux/fs.h:2109 [inline] new_sync_write fs/read_write.c:509 [inline] vfs_write+0xaa8/0xcf5 fs/read_write.c:596 ksys_write+0x19b/0x2bd fs/read_write.c:650 do_syscall_x64 arch/x86/entry/common.c:55 [inline] do_syscall_64+0x51/0xba arch/x86/entry/common.c:93 entry_SYSCALL_64_after_hwframe+0x61/0xcb -> #1 (&data->open_mutex){+.+.}-{3:3}: __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599 __mutex_lock kernel/locking/mutex.c:732 [inline] mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784 vhci_send_frame+0x68/0x9c drivers/bluetooth/hci_vhci.c:75 hci_send_frame+0x1cc/0x2ff net/bluetooth/hci_core.c:2989 hci_sched_acl_pkt net/bluetooth/hci_core.c:3498 [inline] hci_sched_acl net/bluetooth/hci_core.c:3583 [inline] hci_tx_work+0xb94/0x1a60 net/bluetooth/hci_core.c:3654 process_one_work+0x901/0xfb8 kernel/workqueue.c:2310 worker_thread+0xa67/0x1003 kernel/workqueue.c:2457 kthread+0x36a/0x430 kernel/kthread.c:319 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298 -> #0 ((work_completion)(&hdev->tx_work)){+.+.}-{0:0}: check_prev_add kernel/locking/lockdep.c:3053 [inline] check_prevs_add kernel/locking/lockdep.c:3172 [inline] validate_chain kernel/locking/lockdep.c:3787 [inline] __lock_acquire+0x2d32/0x77fa kernel/locking/lockdep.c:5011 lock_acquire+0x273/0x4d5 kernel/locking/lockdep.c:5622 __flush_work+0xee/0x19f kernel/workqueue.c:3090 hci_dev_close_sync+0x32f/0x1113 net/bluetooth/hci_sync.c:4352 hci_dev_do_close+0x47/0x9f net/bluetooth/hci_core.c:553 hci_rfkill_set_block+0x130/0x1ac net/bluetooth/hci_core.c:935 rfkill_set_block+0x1e6/0x3b8 net/rfkill/core.c:345 rfkill_fop_write+0x2d8/0x672 net/rfkill/core.c:1274 vfs_write+0x277/0xcf5 fs/read_write.c:594 ksys_write+0x19b/0x2bd fs/read_write.c:650 do_syscall_x64 arch/x86/entry/common.c:55 [inline] do_syscall_64+0x51/0xba arch/x86/entry/common.c:93 entry_SYSCALL_64_after_hwframe+0x61/0xcb This change removes the need for acquiring the open_mutex in vhci_send_frame, thus eliminating the potential deadlock while maintaining the required packet ordering. Fixes: 92d4abd ("Bluetooth: vhci: Fix race when opening vhci device") Signed-off-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

…2066 Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks for QCA2066. Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Before setting HCI_INQUIRY bit check if HCI_OP_INQUIRY was really sent otherwise the controller maybe be generating invalid events or, more likely, it is a result of fuzzing tools attempting to test the right behavior of the stack when unexpected events are generated. Link: https://bugzilla.kernel.org/show_bug.cgi?id=218151 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This checks if there are connections before suspending since that may disrupt the connections making it stop receiving any data if remote wakeup is not enabled. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Most functions in `net/bluetooth/lib.c` lack propper documentation. This patch adds documentation to all exported functions in `net/bluetooth/lib.c`. Unnecessary or redundant comments are also removed to ensure the file looks clean. Signed-off-by: Yuran Pereira <yuran.pereira@hotmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Intel Read Version event contains a TLV(0x32) having firmware sha1 in operational image. Signed-off-by: Kiran K <kiran.k@intel.com>

Petr Machata says: ==================== selftests: Fixes for kernel CI As discussed on the bi-weekly call on Jan 30, and in mailing around kernel CI effort, some changes are desirable in the suite of forwarding selftests the better to work with the CI tooling. Namely: - The forwarding selftests use a configuration file where names of interfaces are defined and various variables can be overridden. There is also forwarding.config.sample that users can use as a template to refer to when creating the config file. What happens a fair bit is that users either do not know about this at all, or simply forget, and are confused by cryptic failures about interfaces that cannot be created. In patches #1 - #3 have lib.sh just be the single source of truth with regards to which variables exist. That includes the topology variables which were previously only in the sample file, and any "tweak variables", such as what tools to use, sleep times, etc. forwarding.config.sample then becomes just a placeholder with a couple examples. Unless specific HW should be exercised, or specific tools used, the defaults are usually just fine. - Several net/forwarding/ selftests (and one net/ one) cannot be run on veth pairs, they need an actual HW interface to run on. They are generic in the sense that any capable HW should pass them, which is why they have been put to net/forwarding/ as opposed to drivers/net/, but they do not generalize to veth. The fact that these tests are in net/forwarding/, but still complaining when run, is confusing. In patches #4 - #6 move these tests to a new directory drivers/net/hw. - The following patches extend the codebase to handle well test results other than pass and fail. Patch #7 is preparatory. It converts several log_test_skip to XFAIL, so that tests do not spuriously end up returning non-0 when they are not supposed to. In patches #8 - #10, introduce some missing ksft constants, then support having those constants in RET, and then finally in EXIT_STATUS. - The traffic scheduler tests generate a large amount of network traffic to test the behavior of the scheduler. This demands a relatively high-performance computer. On slow machines, such as with a debugging kernel, the test would spuriously fail. It can still be useful to "go through the motions" though, to possibly catch bugs in setup of the scheduler graph and passing packets around. Thus we still want to run the tests, just with lowered demands. To that end, in patches #11 - #12, introduce an environment variable KSFT_MACHINE_SLOW, with obvious meaning. Tests can then make checks more lenient, such as mark failures as XFAIL. A helper, xfail_on_slow, is provided to mark performance-sensitive parts of the selftest. - In patch #13, use a similar mechanism to mark a NH group stats selftest to XFAIL HW stats tests when run on VETH pairs. - All these changes complicate the hitherto straightforward logging and checking logic, so in patch #14, add a selftest that checks this functionality in lib.sh. v1 (vs. an RFC circulated through linux-kselftest): - Patch #9: - Clarify intended usage by s/set_ret/ret_set_ksft_status/, s/nret/ksft_status/ ==================== Link: https://lore.kernel.org/r/cover.1711464583.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

syzkaller reported infinite recursive calls of fib6_dump_done() during netlink socket destruction. [1] From the log, syzkaller sent an AF_UNSPEC RTM_GETROUTE message, and then the response was generated. The following recvmmsg() resumed the dump for IPv6, but the first call of inet6_dump_fib() failed at kzalloc() due to the fault injection. [0] 12:01:34 executing program 3: r0 = socket$nl_route(0x10, 0x3, 0x0) sendmsg$nl_route(r0, ... snip ...) recvmmsg(r0, ... snip ...) (fail_nth: 8) Here, fib6_dump_done() was set to nlk_sk(sk)->cb.done, and the next call of inet6_dump_fib() set it to nlk_sk(sk)->cb.args[3]. syzkaller stopped receiving the response halfway through, and finally netlink_sock_destruct() called nlk_sk(sk)->cb.done(). fib6_dump_done() calls fib6_dump_end() and nlk_sk(sk)->cb.done() if it is still not NULL. fib6_dump_end() rewrites nlk_sk(sk)->cb.done() by nlk_sk(sk)->cb.args[3], but it has the same function, not NULL, calling itself recursively and hitting the stack guard page. To avoid the issue, let's set the destructor after kzalloc(). [0]: FAULT_INJECTION: forcing a failure. name failslab, interval 1, probability 0, space 0, times 0 CPU: 1 PID: 432110 Comm: syz-executor.3 Not tainted 6.8.0-12821-g537c2e91d354-dirty #11 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:117) should_fail_ex (lib/fault-inject.c:52 lib/fault-inject.c:153) should_failslab (mm/slub.c:3733) kmalloc_trace (mm/slub.c:3748 mm/slub.c:3827 mm/slub.c:3992) inet6_dump_fib (./include/linux/slab.h:628 ./include/linux/slab.h:749 net/ipv6/ip6_fib.c:662) rtnl_dump_all (net/core/rtnetlink.c:4029) netlink_dump (net/netlink/af_netlink.c:2269) netlink_recvmsg (net/netlink/af_netlink.c:1988) ____sys_recvmsg (net/socket.c:1046 net/socket.c:2801) ___sys_recvmsg (net/socket.c:2846) do_recvmmsg (net/socket.c:2943) __x64_sys_recvmmsg (net/socket.c:3041 net/socket.c:3034 net/socket.c:3034) [1]: BUG: TASK stack guard page was hit at 00000000f2fa9af1 (stack is 00000000b7912430..000000009a436beb) stack guard page: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 223719 Comm: kworker/1:3 Not tainted 6.8.0-12821-g537c2e91d354-dirty #11 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 Workqueue: events netlink_sock_destruct_work RIP: 0010:fib6_dump_done (net/ipv6/ip6_fib.c:570) Code: 3c 24 e8 f3 e9 51 fd e9 28 fd ff ff 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 41 57 41 56 41 55 41 54 55 48 89 fd <53> 48 8d 5d 60 e8 b6 4d 07 fd 48 89 da 48 b8 00 00 00 00 00 fc ff RSP: 0018:ffffc9000d980000 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffffffff84405990 RCX: ffffffff844059d3 RDX: ffff8881028e0000 RSI: ffffffff84405ac2 RDI: ffff88810c02f358 RBP: ffff88810c02f358 R08: 0000000000000007 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000224 R12: 0000000000000000 R13: ffff888007c82c78 R14: ffff888007c82c68 R15: ffff888007c82c68 FS: 0000000000000000(0000) GS:ffff88811b100000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffc9000d97fff8 CR3: 0000000102309002 CR4: 0000000000770ef0 PKRU: 55555554 Call Trace: <#DF> </#DF> <TASK> fib6_dump_done (net/ipv6/ip6_fib.c:572 (discriminator 1)) fib6_dump_done (net/ipv6/ip6_fib.c:572 (discriminator 1)) ... fib6_dump_done (net/ipv6/ip6_fib.c:572 (discriminator 1)) fib6_dump_done (net/ipv6/ip6_fib.c:572 (discriminator 1)) netlink_sock_destruct (net/netlink/af_netlink.c:401) __sk_destruct (net/core/sock.c:2177 (discriminator 2)) sk_destruct (net/core/sock.c:2224) __sk_free (net/core/sock.c:2235) sk_free (net/core/sock.c:2246) process_one_work (kernel/workqueue.c:3259) worker_thread (kernel/workqueue.c:3329 kernel/workqueue.c:3416) kthread (kernel/kthread.c:388) ret_from_fork (arch/x86/kernel/process.c:153) ret_from_fork_asm (arch/x86/entry/entry_64.S:256) Modules linked in: Fixes: 1da177e ("Linux-2.6.12-rc2") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20240401211003.25274-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Petr Machata says: ==================== mlxsw: Preparations for improving performance Amit Cohen writes: mlxsw driver will use NAPI for event processing in a next patch set. Some additional improvements will be added later. This patch set prepares the code for NAPI usage and refactor some relevant areas. See more details in commit messages. Patch Set overview: Patches #1-#2 are preparations for patch #3 Patch #3 setups tasklets as part of queue initializtion Patch #4 removes handling of unlikely scenario Patch #5 removes unused counters Patch #6 makes style change in mlxsw_pci_eq_tasklet() Patch #7-#10 poll command interface instead of EQ0 usage Patches #11-#12 make style change and break the function mlxsw_pci_cq_tasklet() Patches #13-#14 remove functions which can be replaced by a stored value Patch #15 improves accessing to descriptor queue instance ==================== Link: https://lore.kernel.org/r/cover.1712062203.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

vhost_worker will call tun call backs to receive packets. If too many illegal packets arrives, tun_do_read will keep dumping packet contents. When console is enabled, it will costs much more cpu time to dump packet and soft lockup will be detected. net_ratelimit mechanism can be used to limit the dumping rate. PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980" #0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253 #1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3 #2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e #3 [fffffe00003fced0] do_nmi at ffffffff8922660d #4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663 [exception RIP: io_serial_in+20] RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002 RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000 RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0 RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020 R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #5 [ffffa655314979e8] io_serial_in at ffffffff89792594 #6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470 #7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6 #8 [ffffa65531497a20] uart_console_write at ffffffff8978b605 #9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558 #10 [ffffa65531497ac8] console_unlock at ffffffff89316124 #11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07 #12 [ffffa65531497b68] printk at ffffffff89318306 #13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765 #14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun] #15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun] #16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net] #17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost] #18 [ffffa65531497f10] kthread at ffffffff892d2e72 #19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f Fixes: ef3db4a ("tun: avoid BUG, dump packet on GSO errors") Signed-off-by: Lei Chen <lei.chen@smartx.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The dev_tracker is added to ax25_cb in ax25_bind(). When the ax25 device is detaching, the dev_tracker of ax25_cb should be deallocated in ax25_kill_by_device() instead of the dev_tracker of ax25_dev. The log reported by ref_tracker is shown below: [ 80.884935] ref_tracker: reference already released. [ 80.885150] ref_tracker: allocated in: [ 80.885349] ax25_dev_device_up+0x105/0x540 [ 80.885730] ax25_device_event+0xa4/0x420 [ 80.885730] notifier_call_chain+0xc9/0x1e0 [ 80.885730] __dev_notify_flags+0x138/0x280 [ 80.885730] dev_change_flags+0xd7/0x180 [ 80.885730] dev_ifsioc+0x6a9/0xa30 [ 80.885730] dev_ioctl+0x4d8/0xd90 [ 80.885730] sock_do_ioctl+0x1c2/0x2d0 [ 80.885730] sock_ioctl+0x38b/0x4f0 [ 80.885730] __se_sys_ioctl+0xad/0xf0 [ 80.885730] do_syscall_64+0xc4/0x1b0 [ 80.885730] entry_SYSCALL_64_after_hwframe+0x67/0x6f [ 80.885730] ref_tracker: freed in: [ 80.885730] ax25_device_event+0x272/0x420 [ 80.885730] notifier_call_chain+0xc9/0x1e0 [ 80.885730] dev_close_many+0x272/0x370 [ 80.885730] unregister_netdevice_many_notify+0x3b5/0x1180 [ 80.885730] unregister_netdev+0xcf/0x120 [ 80.885730] sixpack_close+0x11f/0x1b0 [ 80.885730] tty_ldisc_kill+0xcb/0x190 [ 80.885730] tty_ldisc_hangup+0x338/0x3d0 [ 80.885730] __tty_hangup+0x504/0x740 [ 80.885730] tty_release+0x46e/0xd80 [ 80.885730] __fput+0x37f/0x770 [ 80.885730] __x64_sys_close+0x7b/0xb0 [ 80.885730] do_syscall_64+0xc4/0x1b0 [ 80.885730] entry_SYSCALL_64_after_hwframe+0x67/0x6f [ 80.893739] ------------[ cut here ]------------ [ 80.894030] WARNING: CPU: 2 PID: 140 at lib/ref_tracker.c:255 ref_tracker_free+0x47b/0x6b0 [ 80.894297] Modules linked in: [ 80.894929] CPU: 2 PID: 140 Comm: ax25_conn_rel_6 Not tainted 6.9.0-rc4-g8cd26fd90c1a #11 [ 80.895190] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qem4 [ 80.895514] RIP: 0010:ref_tracker_free+0x47b/0x6b0 [ 80.895808] Code: 83 c5 18 4c 89 eb 48 c1 eb 03 8a 04 13 84 c0 0f 85 df 01 00 00 41 83 7d 00 00 75 4b 4c 89 ff 9 [ 80.896171] RSP: 0018:ffff888009edf8c0 EFLAGS: 00000286 [ 80.896339] RAX: 1ffff1100141ac00 RBX: 1ffff1100149463b RCX: dffffc0000000000 [ 80.896502] RDX: 0000000000000001 RSI: 0000000000000246 RDI: ffff88800a0d6518 [ 80.896925] RBP: ffff888009edf9b0 R08: ffff88806d3288d3 R09: 1ffff1100da6511a [ 80.897212] R10: dffffc0000000000 R11: ffffed100da6511b R12: ffff88800a4a31d4 [ 80.897859] R13: ffff88800a4a31d8 R14: dffffc0000000000 R15: ffff88800a0d6518 [ 80.898279] FS: 00007fd88b7fe700(0000) GS:ffff88806d300000(0000) knlGS:0000000000000000 [ 80.899436] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 80.900181] CR2: 00007fd88c001d48 CR3: 000000000993e000 CR4: 00000000000006f0 ... [ 80.935774] ref_tracker: sp%d@000000000bb9df3d has 1/1 users at [ 80.935774] ax25_bind+0x424/0x4e0 [ 80.935774] __sys_bind+0x1d9/0x270 [ 80.935774] __x64_sys_bind+0x75/0x80 [ 80.935774] do_syscall_64+0xc4/0x1b0 [ 80.935774] entry_SYSCALL_64_after_hwframe+0x67/0x6f Change ax25_dev->dev_tracker to the dev_tracker of ax25_cb in order to mitigate the bug. Fixes: feef318 ("ax25: fix UAF bugs of net_device caused by rebinding operation") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/20240419020456.29826-1-duoming@zju.edu.cn Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Wen Gu says: ==================== net/smc: SMC intra-OS shortcut with loopback-ism This patch set acts as the second part of the new version of [1] (The first part can be referred from [2]), the updated things of this version are listed at the end. - Background SMC-D is now used in IBM z with ISM function to optimize network interconnect for intra-CPC communications. Inspired by this, we try to make SMC-D available on the non-s390 architecture through a software-implemented Emulated-ISM device, that is the loopback-ism device here, to accelerate inter-process or inter-containers communication within the same OS instance. - Design This patch set includes 3 parts: - Patch #1: some prepare work for loopback-ism. - Patch #2-#7: implement loopback-ism device and adapt SMC-D for it. loopback-ism now serves only SMC and no userspace interfaces exposed. - Patch #8-#11: memory copy optimization for intra-OS scenario. The loopback-ism device is designed as an ISMv2 device and not be limited to a specific net namespace, ends of both inter-process connection (1/1' in diagram below) or inter-container connection (2/2' in diagram below) can find the same available loopback-ism and choose it during the CLC handshake. Container 1 (ns1) Container 2 (ns2) +-----------------------------------------+ +-------------------------+ | +-------+ +-------+ +-------+ | | +-------+ | | | App A | | App B | | App C | | | | App D |<-+ | | +-------+ +---^---+ +-------+ | | +-------+ |(2') | | |127.0.0.1 (1')| |192.168.0.11 192.168.0.12| | | (1)| +--------+ | +--------+ |(2) | | +--------+ +--------+ | | `-->| lo |-` | eth0 |<-` | | | lo | | eth0 | | +---------+--|---^-+---+-----|--+---------+ +-+--------+---+-^------+-+ | | | | Kernel | | | | +----+-------v---+-----------v----------------------------------+---+----+ | | TCP | | | | | | | +--------------------------------------------------------------+ | | | | +--------------+ | | | smc loopback | | +---------------------------+--------------+-----------------------------+ loopback-ism device creates DMBs (shared memory) for each connection peer. Since data transfer occurs within the same kernel, the sndbuf of each peer is only a descriptor and point to the same memory region as peer DMB, so that the data copy from sndbuf to peer DMB can be avoided in loopback-ism case. Container 1 (ns1) Container 2 (ns2) +-----------------------------------------+ +-------------------------+ | +-------+ | | +-------+ | | | App C |-----+ | | | App D | | | +-------+ | | | +-^-----+ | | | | | | | | (2) | | | (2') | | | | | | | | +---------------|-------------------------+ +----------|--------------+ | | Kernel | | +---------------|-----------------------------------------|--------------+ | +--------+ +--v-----+ +--------+ +--------+ | | |dmb_desc| |snd_desc| |dmb_desc| |snd_desc| | | +-----|--+ +--|-----+ +-----|--+ +--------+ | | +-----|--+ | +-----|--+ | | | DMB C | +---------------------------------| DMB D | | | +--------+ +--------+ | | | | +--------------+ | | | smc loopback | | +---------------------------+--------------+-----------------------------+ - Benchmark Test * Test environments: - VM with Intel Xeon Platinum 8 core 2.50GHz, 16 GiB mem. - SMC sndbuf/DMB size 1MB. * Test object: - TCP: run on TCP loopback. - SMC lo: run on SMC loopback-ism. 1. ipc-benchmark (see [3]) - ./<foo> -c 1000000 -s 100 TCP SMC-lo Message rate (msg/s) 84991 151293(+78.01%) 2. sockperf - serv: <smc_run> sockperf sr --tcp - clnt: <smc_run> sockperf { tp | pp } --tcp --msg-size={ 64000 for tp | 14 for pp } -i 127.0.0.1 -t 30 TCP SMC-lo Bandwidth(MBps) 5033.569 7987.732(+58.69%) Latency(us) 5.986 3.398(-43.23%) 3. nginx/wrk - serv: <smc_run> nginx - clnt: <smc_run> wrk -t 8 -c 1000 -d 30 http://127.0.0.1:80 TCP SMC-lo Requests/s 187951.76 267107.90(+42.12%) 4. redis-benchmark - serv: <smc_run> redis-server - clnt: <smc_run> redis-benchmark -h 127.0.0.1 -q -t set,get -n 400000 -c 200 -d 1024 TCP SMC-lo GET(Requests/s) 86132.64 118133.49(+37.15%) SET(Requests/s) 87374.40 122887.86(+40.65%) Change log: v7->v6 - Patch #2: minor: remove unnecessary 'return' of inline smc_loopback_exit(). - Patch #10: minor: directly return 0 instead of 'rc' in smcd_cdc_msg_send(). - all: collect the Reviewed-by tags. v6->RFC v5 Link: https://lore.kernel.org/netdev/20240414040304.54255-1-guwen@linux.alibaba.com/ - Patch #2: make the use of CONFIG_SMC_LO cleaner. - Patch #5: mark some smcd_ops that loopback-ism doesn't support as optional and check for the support when they are called. - Patch #7: keep loopback-ism at the beginning of the SMC-D device list. - Some expression changes in commit logs and comments. RFC v5->RFC v4: Link: https://lore.kernel.org/netdev/20240324135522.108564-1-guwen@linux.alibaba.com/ - Patch #2: minor changes in description of config SMC_LO and comments. - Patch #10: minor changes in comments and if(smc_ism_support_dmb_nocopy()) check in smcd_cdc_msg_send(). - Patch #3: change smc_lo_generate_id() to smc_lo_generate_ids() and SMC_LO_CHID to SMC_LO_RESERVED_CHID. - Patch #5: memcpy while holding the ldev->dmb_ht_lock. - Some expression changes in commit logs. RFC v4->v3: Link: https://lore.kernel.org/netdev/20240317100545.96663-1-guwen@linux.alibaba.com/ - The merge window of v6.9 is open, so post this series as an RFC. - Patch #6: since some information fed back by smc_nl_handle_smcd_dev() dose not apply to Emulated-ISM (including loopback-ism here), loopback-ism is not exposed through smc netlink for the time being. we may refactor this part when smc netlink interface is updated. v3->v2: Link: https://lore.kernel.org/netdev/20240312142743.41406-1-guwen@linux.alibaba.com/ - Patch #11: use tasklet_schedule(&conn->rx_tsklet) instead of smcd_cdc_rx_handler() to avoid possible recursive locking of conn->send_lock and use {read|write}_lock_bh() to acquire dmb_ht_lock. v2->v1: Link: https://lore.kernel.org/netdev/20240307095536.29648-1-guwen@linux.alibaba.com/ - All the patches: changed the term virtual-ISM to Emulated-ISM as defined by SMCv2.1. - Patch #3: optimized the description of SMC_LO config. Avoid exposing loopback-ism to sysfs and remove all the knobs until future definition clear. - Patch #3: try to make lockdep happy by using read_lock_bh() in smc_lo_move_data(). - Patch #6: defaultly use physical contiguous DMB buffers. - Patch #11: defaultly enable DMB no-copy for loopback-ism and free the DMB in unregister_dmb or detach_dmb when dmb_node->refcnt reaches 0, instead of using wait_event to keep waiting in unregister_dmb. v1->RFC: Link: https://lore.kernel.org/netdev/20240111120036.109903-1-guwen@linux.alibaba.com/ - Patch #9: merge rx_bytes and tx_bytes as xfer_bytes statistics: /sys/devices/virtual/smc/loopback-ism/xfer_bytes - Patch #10: add support_dmb_nocopy operation to check if SMC-D device supports merging sndbuf with peer DMB. - Patch #13 & #14: introduce loopback-ism device control of DMB memory type and control of whether to merge sndbuf and DMB. They can be respectively set by: /sys/devices/virtual/smc/loopback-ism/dmb_type /sys/devices/virtual/smc/loopback-ism/dmb_copy The motivation for these two control is that a performance bottleneck was found when using vzalloced DMB and sndbuf is merged with DMB, and there are many CPUs and CONFIG_HARDENED_USERCOPY is set [4]. The bottleneck is caused by the lock contention in vmap_area_lock [5] which is involved in memcpy_from_msg() or memcpy_to_msg(). Currently, Uladzislau Rezki is working on mitigating the vmap lock contention [6]. It has significant effects, but using virtual memory still has additional overhead compared to using physical memory. So this new version provides controls of dmb_type and dmb_copy to suit different scenarios. - Some minor changes and comments improvements. RFC->old version([1]): Link: https://lore.kernel.org/netdev/1702214654-32069-1-git-send-email-guwen@linux.alibaba.com/ - Patch #1: improve the loopback-ism dump, it shows as follows now: # smcd d FID Type PCI-ID PCHID InUse #LGs PNET-ID 0000 0 loopback-ism ffff No 0 - Patch #3: introduce the smc_ism_set_v2_capable() helper and set smc_ism_v2_capable when ISMv2 or virtual ISM is registered, regardless of whether there is already a device in smcd device list. - Patch #3: loopback-ism will be added into /sys/devices/virtual/smc/loopback-ism/. - Patch #8: introduce the runtime switch /sys/devices/virtual/smc/loopback-ism/active to activate or deactivate the loopback-ism. - Patch #9: introduce the statistics of loopback-ism by /sys/devices/virtual/smc/loopback-ism/{{tx|rx}_tytes|dmbs_cnt}. - Some minor changes and comments improvements. [1] https://lore.kernel.org/netdev/1695568613-125057-1-git-send-email-guwen@linux.alibaba.com/ [2] https://lore.kernel.org/netdev/20231219142616.80697-1-guwen@linux.alibaba.com/ [3] https://github.com/goldsborough/ipc-bench [4] https://lore.kernel.org/all/3189e342-c38f-6076-b730-19a6efd732a5@linux.alibaba.com/ [5] https://lore.kernel.org/all/238e63cd-e0e8-4fbf-852f-bc4d5bc35d5a@linux.alibaba.com/ [6] https://lore.kernel.org/all/20240102184633.748113-1-urezki@gmail.com/ ==================== Link: https://lore.kernel.org/r/20240428060738.60843-1-guwen@linux.alibaba.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>

…/git/pablo/gtp Pablo neira Ayuso says: ==================== gtp pull request 24-05-07 This v3 includes: - fix for clang uninitialized variable per Jakub. - address Smatch and Coccinelle reports per Simon - remove inline in new IPv6 support per Simon - fix memleaks in netlink control plane per Simon -o- The following patchset contains IPv6 GTP driver support for net-next, this also includes IPv6 over IPv4 and vice-versa: Patch #1 removes a unnecessary stack variable initialization in the socket routine. Patch #2 deals with GTP extension headers. This variable length extension header to decapsulate packets accordingly. Otherwise, packets are dropped when these extension headers are present which breaks interoperation with other non-Linux based GTP implementations. Patch #3 prepares for IPv6 support by moving IPv4 specific fields in PDP context objects to a union. Patch #4 adds IPv6 support while retaining backward compatibility. Three new attributes allows to declare an IPv6 GTP tunnel GTPA_FAMILY, GTPA_PEER_ADDR6 and GTPA_MS_ADDR6 as well as IFLA_GTP_LOCAL6 to declare the IPv6 GTP UDP socket. Up to this patch, only IPv6 outer in IPv6 inner is supported. Patch #5 uses IPv6 address /64 prefix for UE/MS in the inner headers. Unlike IPv4, which provides a 1:1 mapping between UE/MS, IPv6 tunnel encapsulates traffic for /64 address as specified by 3GPP TS. Patch has been split from Patch #4 to highlight this behaviour. Patch #6 passes up IPv6 link-local traffic, such as IPv6 SLAAC, for handling to userspace so they are handled as control packets. Patch #7 prepares to allow for GTP IPv4 over IPv6 and vice-versa by moving IP specific debugging out of the function to build IPv4 and IPv6 GTP packets. Patch #8 generalizes TOS/DSCP handling following similar approach as in the existing iptunnel infrastructure. Patch #9 adds a helper function to build an IPv4 GTP packet in the outer header. Patch #10 adds a helper function to build an IPv6 GTP packet in the outer header. Patch #11 adds support for GTP IPv4-over-IPv6 and vice-versa. Patch #12 allows to use the same TID/TEID (tunnel identifier) for inner IPv4 and IPv6 packets for better UE/MS dual stack integration. This series integrates with the osmocom.org project CI and TTCN-3 test infrastructure (Oliver Smith) as well as the userspace libgtpnl library. Thanks to Harald Welte, Oliver Smith and Pau Espin for reviewing and providing feedback through the osmocom.org redmine platform to make this happen. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the dma_unmap_page_attrs() call in the driver's XDP_REDIRECT code path. This should have been removed when we let the page pool handle the DMA mapping. This bug causes the warning: WARNING: CPU: 7 PID: 59 at drivers/iommu/dma-iommu.c:1198 iommu_dma_unmap_page+0xd5/0x100 CPU: 7 PID: 59 Comm: ksoftirqd/7 Tainted: G W 6.8.0-1010-gcp #11-Ubuntu Hardware name: Dell Inc. PowerEdge R7525/0PYVT1, BIOS 2.15.2 04/02/2024 RIP: 0010:iommu_dma_unmap_page+0xd5/0x100 Code: 89 ee 48 89 df e8 cb f2 69 ff 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 31 d2 31 c9 31 f6 31 ff 45 31 c0 e9 ab 17 71 00 <0f> 0b 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 31 d2 31 c9 RSP: 0018:ffffab1fc0597a48 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff99ff838280c8 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffab1fc0597a78 R08: 0000000000000002 R09: ffffab1fc0597c1c R10: ffffab1fc0597cd3 R11: ffff99ffe375acd8 R12: 00000000e65b9000 R13: 0000000000000050 R14: 0000000000001000 R15: 0000000000000002 FS: 0000000000000000(0000) GS:ffff9a06efb80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000565c34c37210 CR3: 00000005c7e3e000 CR4: 0000000000350ef0 ? show_regs+0x6d/0x80 ? __warn+0x89/0x150 ? iommu_dma_unmap_page+0xd5/0x100 ? report_bug+0x16a/0x190 ? handle_bug+0x51/0xa0 ? exc_invalid_op+0x18/0x80 ? iommu_dma_unmap_page+0xd5/0x100 ? iommu_dma_unmap_page+0x35/0x100 dma_unmap_page_attrs+0x55/0x220 ? bpf_prog_4d7e87c0d30db711_xdp_dispatcher+0x64/0x9f bnxt_rx_xdp+0x237/0x520 [bnxt_en] bnxt_rx_pkt+0x640/0xdd0 [bnxt_en] __bnxt_poll_work+0x1a1/0x3d0 [bnxt_en] bnxt_poll+0xaa/0x1e0 [bnxt_en] __napi_poll+0x33/0x1e0 net_rx_action+0x18a/0x2f0 Fixes: 578fcfd ("bnxt_en: Let the page pool manage the DMA mapping") Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20240820203415.168178-1-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A sysfs reader can race with a device reset or removal, attempting to read device state when the device is not actually present. eg: [exception RIP: qed_get_current_link+17] #8 [ffffb9e4f2907c48] qede_get_link_ksettings at ffffffffc07a994a [qede] #9 [ffffb9e4f2907cd8] __rh_call_get_link_ksettings at ffffffff992b01a3 #10 [ffffb9e4f2907d38] __ethtool_get_link_ksettings at ffffffff992b04e4 #11 [ffffb9e4f2907d90] duplex_show at ffffffff99260300 #12 [ffffb9e4f2907e38] dev_attr_show at ffffffff9905a01c #13 [ffffb9e4f2907e50] sysfs_kf_seq_show at ffffffff98e0145b #14 [ffffb9e4f2907e68] seq_read at ffffffff98d902e3 #15 [ffffb9e4f2907ec8] vfs_read at ffffffff98d657d1 #16 [ffffb9e4f2907f00] ksys_read at ffffffff98d65c3f #17 [ffffb9e4f2907f38] do_syscall_64 at ffffffff98a052fb crash> struct net_device.state ffff9a9d21336000 state = 5, state 5 is __LINK_STATE_START (0b1) and __LINK_STATE_NOCARRIER (0b100). The device is not present, note lack of __LINK_STATE_PRESENT (0b10). This is the same sort of panic as observed in commit 4224cfd ("net-sysfs: add check for netdevice being present to speed_show"). There are many other callers of __ethtool_get_link_ksettings() which don't have a device presence check. Move this check into ethtool to protect all callers. Fixes: d519e17 ("net: export device speed and duplex via sysfs") Fixes: 4224cfd ("net-sysfs: add check for netdevice being present to speed_show") Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com> Link: https://patch.msgid.link/8bae218864beaa44ed01628140475b9bf641c5b0.1724393671.git.jamie.bainbridge@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Machon says: ==================== net: microchip: add FDMA library and use it for Sparx5 This patch series is the first of a 2-part series, that adds a new common FDMA library for Microchip switch chips Sparx5 and lan966x. These chips share the same FDMA engine, and as such will benefit from a common library with a common implementation. This also has the benefit of removing a lot open-coded bookkeeping and duplicate code for the two drivers. Additionally, upstreaming efforts for a third chip, lan969x, will begin in the near future. This chip will use the new library too. In this first series, the FDMA library is introduced and used by the Sparx5 switch driver. ################### # Example of use: # ################### - Initialize the rx and tx fdma structs with values for: number of DCB's, number of DB's, channel ID, DB size (data buffer size), and total size of the requested memory. Also provide two callbacks: nextptr_cb() and dataptr_cb() for getting the nextptr and dataptr. - Allocate memory using fdma_alloc_phys() or fdma_alloc_coherent(). - Initialize the DCB's with fdma_dcb_init(). - Add new DCB's with fdma_dcb_add(). - Free memory with fdma_free_phys() or fdma_free_coherent(). ##################### # Patch breakdown: # ##################### Patch #1: introduces library and selects it for Sparx5. Patch #2: includes the fdma_api.h header and removes old symbols. Patch #3: replaces old rx and tx variables with equivalent ones from the fdma struct. Only the variables that can be changed without breaking traffic is changed in this patch. Patch #4: uses the library for allocation of rx buffers. This requires quite a bit of refactoring in this single patch. Patch #5: uses the library for adding DCB's in the rx path. Patch #6: uses the library for freeing rx buffers. Patch #7: uses the library helpers in the rx path. Patch #8: uses the library for allocation of tx buffers. This requires quite a bit of refactoring in this single patch. Patch #9: uses the library for adding DCB's in the tx path. Patch #10: uses the library helpers in the tx path. Patch #11: ditches the existing linked list for storing buffer addresses, and instead uses offsets into contiguous memory. Patch #12: modifies existing rx and tx functions to be direction independent. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>

…rnel/git/netfilter/nf-next Pablo Neira Ayuso says: ==================== Netfilter updates for net-next The following patchset contains Netfilter updates for net-next: Patch #1 adds ctnetlink support for kernel side filtering for deletions, from Changliang Wu. Patch #2 updates nft_counter support to Use u64_stats_t, from Sebastian Andrzej Siewior. Patch #3 uses kmemdup_array() in all xtables frontends, from Yan Zhen. Patch #4 is a oneliner to use ERR_CAST() in nf_conntrack instead opencoded casting, from Shen Lichuan. Patch #5 removes unused argument in nftables .validate interface, from Florian Westphal. Patch #6 is a oneliner to correct a typo in nftables kdoc, from Simon Horman. Patch #7 fixes missing kdoc in nftables, also from Simon. Patch #8 updates nftables to handle timeout less than CONFIG_HZ. Patch #9 rejects element expiration if timeout is zero, otherwise it is silently ignored. Patch #10 disallows element expiration larger than timeout. Patch #11 removes unnecessary READ_ONCE annotation while mutex is held. Patch #12 adds missing READ_ONCE/WRITE_ONCE annotation in dynset. Patch #13 annotates data-races around element expiration. Patch #14 allocates timeout and expiration in one single set element extension, they are tighly couple, no reason to keep them separated anymore. Patch #15 updates nftables to interpret zero timeout element as never times out. Note that it is already possible to declare sets with elements that never time out but this generalizes to all kind of set with timeouts. Patch #16 supports for element timeout and expiration updates. * tag 'nf-next-24-09-06' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next: netfilter: nf_tables: set element timeout update support netfilter: nf_tables: zero timeout means element never times out netfilter: nf_tables: consolidate timeout extension for elements netfilter: nf_tables: annotate data-races around element expiration netfilter: nft_dynset: annotate data-races around set timeout netfilter: nf_tables: remove annotation to access set timeout while holding lock netfilter: nf_tables: reject expiration higher than timeout netfilter: nf_tables: reject element expiration with no timeout netfilter: nf_tables: elements with timeout below CONFIG_HZ never expire netfilter: nf_tables: Add missing Kernel doc netfilter: nf_tables: Correct spelling in nf_tables.h netfilter: nf_tables: drop unused 3rd argument from validate callback ops netfilter: conntrack: Convert to use ERR_CAST() netfilter: Use kmemdup_array instead of kmemdup for multiple allocation netfilter: nft_counter: Use u64_stats_t for statistic. netfilter: ctnetlink: support CTA_FILTER for flush ==================== Link: https://patch.msgid.link/20240905232920.5481-1-pablo@netfilter.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Machon says: ==================== net: lan966x: use the newly introduced FDMA library This patch series is the second of a 2-part series [1], that adds a new common FDMA library for Microchip switch chips Sparx5 and lan966x. These chips share the same FDMA engine, and as such will benefit from a common library with a common implementation. This also has the benefit of removing a lot of open-coded bookkeeping and duplicate code for the two drivers. In this second series, the FDMA library will be taken into use by the lan966x switch driver. ################### # Example of use: # ################### - Initialize the rx and tx fdma structs with values for: number of DCB's, number of DB's, channel ID, DB size (data buffer size), and total size of the requested memory. Also provide two callbacks: nextptr_cb() and dataptr_cb() for getting the nextptr and dataptr. - Allocate memory using fdma_alloc_phys() or fdma_alloc_coherent(). - Initialize the DCB's with fdma_dcb_init(). - Add new DCB's with fdma_dcb_add(). - Free memory with fdma_free_phys() or fdma_free_coherent(). ##################### # Patch breakdown: # ##################### Patch #1: select FDMA library for lan966x. Patch #2: includes the fdma_api.h header and removes old symbols. Patch #3: replaces old rx and tx variables with equivalent ones from the fdma struct. Only the variables that can be changed without breaking traffic is changed in this patch. Patch #4: uses the library for allocation of rx buffers. This requires quite a bit of refactoring in this single patch. Patch #5: uses the library for adding DCB's in the rx path. Patch #6: uses the library for freeing rx buffers. Patch #7: uses the library for allocation of tx buffers. This requires quite a bit of refactoring in this single patch. Patch #8: uses the library for adding DCB's in the tx path. Patch #9: uses the library helpers in the tx path. Patch #10: ditch last_in_use variable and use library instead. Patch #11: uses library helpers throughout. Patch #12: refactor lan966x_fdma_reload() function. [1] https://lore.kernel.org/netdev/20240902-fdma-sparx5-v1-0-1e7d5e5a9f34@microchip.com/ Signed-off-by: Daniel Machon <daniel.machon@microchip.com> ==================== Link: https://patch.msgid.link/20240905-fdma-lan966x-v1-0-e083f8620165@microchip.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>

…CAN XL step 3/3" Vincent Mailhol <mailhol@kernel.org> says: In November last year, I sent an RFC to introduce CAN XL [1]. That RFC, despite positive feedback, was put on hold due to some unanswered question concerning the PWM encoding [2]. While stuck, some small preparation work was done in parallel in [3] by refactoring the struct can_priv and doing some trivial clean-up and renaming. Initially, [3] received zero feedback but was eventually merged after splitting it in smaller parts and resending it. Finally, in July this year, we clarified the remaining mysteries about PWM calculation, thus unlocking the series. Summer being a bit busy because of some personal matters brings us to now. After doing all the refactoring and adding all the CAN XL features, the final result is more than 30 patches, definitively too much for a single series. So I am splitting the remaining changes three: - can: rework the CAN MTU logic [4] - can: netlink: preparation before introduction of CAN XL (this series) - CAN XL (will come right after the two preparation series get merged) And thus, this series continues and finishes the preparation work done in [3] and [4]. It contains all the refactoring needed to smoothly introduce CAN XL. The goal is to: - split the functions in smaller pieces: CAN XL will introduce a fair amount of code. And some functions which are already fairly long (86 lines for can_validate(), 215 lines for can_changelink()) would grow to disproportionate sizes if the CAN XL logic were to be inlined in those functions. - repurpose the existing code to handle both CAN FD and CAN XL: a huge part of CAN XL simply reuses the CAN FD logic. All the existing CAN FD logic is made more generic to handle both CAN FD and XL. In more details: - Patch #1 moves struct data_bittiming_params from dev.h to bittiming.h and patch #2 makes can_get_relative_tdco() FD agnostic before also moving it to bittiming.h. - Patch #3 adds some comments to netlink.h tagging which IFLA symbols are FD specific. - Patches #4 to #6 are refactoring can_validate() and can_validate_bittiming(). - Patches #7 to #11 are refactoring can_changelink() and can_tdc_changelink(). - Patches #12 and #13 are refactoring can_get_size() and can_tdc_get_size(). - Patches #14 to #17 are refactoring can_fill_info() and can_tdc_fill_info(). - Patch #18 makes can_calc_tdco() FD agnostic. - Patch #19 adds can_get_ctrlmode_str() which converts control mode flags into strings. This is done in preparation of patch #20. - Patch #20 is the final patch and improves the user experience by providing detailed error messages whenever invalid parameters are provided. All those error messages came into handy when debugging the upcoming CAN XL patches. Aside from the last patch, the other changes do not impact any of the existing functionalities. The follow up series which introduces CAN XL is nearly completed but will be sent only once this one is approved: one thing at a time, I do not want to overwhelm people (including myself). [1] https://lore.kernel.org/linux-can/20241110155902.72807-16-mailhol.vincent@wanadoo.fr/ [2] https://lore.kernel.org/linux-can/c4771c16-c578-4a6d-baee-918fe276dbe9@wanadoo.fr/ [3] https://lore.kernel.org/linux-can/20241110155902.72807-16-mailhol.vincent@wanadoo.fr/ [4] https://lore.kernel.org/linux-can/20250923-can-fix-mtu-v2-0-984f9868db69@kernel.org/ Link: https://patch.msgid.link/20250923-canxl-netlink-prep-v4-0-e720d28f66fe@kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Vudentz and others added 9 commits October 24, 2023 10:40

Bluetooth: ISO: Allow binding a PA sync socket

0783375

This makes it possible to bind a PA sync socket to a number of BISes before issuing the BIG Create Sync command. Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: qca: Set both WIDEBAND_SPEECH and LE_STATES quirks for QCA…

d574237

…2066 Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks for QCA2066. Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btusb: Don't suspend when there are connections

d4a9d62

This checks if there are connections before suspending since that may disrupt the connections making it stop receiving any data if remote wakeup is not enabled. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth:btintel: Print firmware SHA1

6ecb4c8

Intel Read Version event contains a TLV(0x32) having firmware sha1 in operational image. Signed-off-by: Kiran K <kiran.k@intel.com>

BluezTestBot force-pushed the master branch 2 times, most recently from dea290e to 8f0ca5a Compare December 19, 2023 18:41

BluezTestBot force-pushed the master branch from 8f0ca5a to da9065c Compare December 22, 2023 18:22

BluezTestBot force-pushed the master branch from 5e35f82 to a93e9d5 Compare February 2, 2024 21:17

BluezTestBot force-pushed the master branch from 1405ad2 to 48201a3 Compare March 7, 2024 18:14

BluezTestBot force-pushed the master branch 2 times, most recently from 2216e1e to 4d0d849 Compare April 2, 2024 16:13

BluezTestBot force-pushed the master branch from 54b5315 to 215c470 Compare April 8, 2024 22:13

BluezTestBot force-pushed the master branch from 48a9e64 to 0a0f901 Compare April 25, 2024 16:40

BluezTestBot force-pushed the master branch from 0172c23 to aa63c8b Compare April 30, 2024 22:12

BluezTestBot force-pushed the master branch 2 times, most recently from 5c7d0f2 to f7bbc1e Compare May 3, 2024 17:11

BluezTestBot force-pushed the master branch from 93e3117 to 3b42b64 Compare May 15, 2024 21:19

BluezTestBot force-pushed the master branch from 0b22b7f to 5fe0be8 Compare June 10, 2024 13:41

BluezTestBot force-pushed the master branch from f2ed8d6 to 7285ef0 Compare August 15, 2024 17:13

BluezTestBot force-pushed the master branch from 4e72805 to 61bea69 Compare August 23, 2024 20:14

BluezTestBot force-pushed the master branch from fd8c0f8 to 7b05933 Compare September 12, 2024 16:47

BluezTestBot force-pushed the master branch from a5f3fa7 to cc34f7a Compare September 27, 2024 15:22

BluezTestBot force-pushed the master branch from c3d1fd9 to 5fe50b4 Compare October 16, 2024 18:50

BluezTestBot force-pushed the master branch from f8e802a to 827af47 Compare November 14, 2024 21:22

BluezTestBot force-pushed the master branch from 1f2ae3f to 26fbd34 Compare January 15, 2025 16:20

BluezTestBot force-pushed the master branch 2 times, most recently from 3f20f3d to 2fc8906 Compare February 21, 2025 21:17

BluezTestBot force-pushed the master branch from ebbeaff to 01aa727 Compare March 4, 2025 14:46

BluezTestBot force-pushed the master branch 3 times, most recently from 402f429 to eed14eb Compare March 25, 2025 19:41

BluezTestBot force-pushed the master branch 2 times, most recently from 17487bc to 3aa1dc3 Compare May 22, 2025 17:20

BluezTestBot force-pushed the master branch from 6f40d15 to b866edd Compare July 16, 2025 13:54

BluezTestBot force-pushed the master branch 4 times, most recently from c508020 to 9c53399 Compare July 29, 2025 18:21

BluezTestBot force-pushed the master branch 2 times, most recently from 8d0a157 to be812ac Compare September 27, 2025 15:48

BluezTestBot force-pushed the master branch from 8d2c47a to af8a2b9 Compare October 24, 2025 14:23

BluezTestBot force-pushed the master branch from b026958 to 525459d Compare December 1, 2025 21:32

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Uh oh!

Bluetooth:btintel: Print firmware SHA1 #11

Bluetooth:btintel: Print firmware SHA1 #11

Uh oh!

kirankrishnappa-intel commented Nov 23, 2023

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

4 participants

Bluetooth:btintel: Print firmware SHA1 #11

Are you sure you want to change the base?

Bluetooth:btintel: Print firmware SHA1 #11

Uh oh!

Conversation

kirankrishnappa-intel commented Nov 23, 2023

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

4 participants